1、 Lack of material
Después de que el material fundido ingresa a la cavidad del molde, no se llena por completo, lo que resulta en la escasez de piezas de plástico.
Causas y contramedidas:
(1)Improper selection of equipment: when selecting equipment, the amount of melt glue on the machine must be greater than the amount of melt glue on the products, and the weight of piezas moldeadas por inyección can only account for 85% of the total amount of melt glue on the machine.
(2) Insufficient material supply: if there is bridging phenomenon at the feeding port, the screw injection stroke can be increased appropriately to increase the material supply.
(3) Poor fluidity of raw materials: improve the retention defects of the mold pouring system, reasonably set the pouring position, expand the gate, flow channel and the size of the injection gate, and use a larger nozzle to properly increase the temperature of raw materials.
(4) Unreasonable design of gating system: when designing gating system, attention should be paid to gate balance, which is proportional to the weight of plastic parts in the mold cavity and gate size. It is that each mold cavity can be filled at the same time. The gate position should be selected at the original wall position, or the design scheme of balanced layout of runner can be adopted.
(5) Mal escape del molde: verifique si hay una cavidad de material fría o si la posición es correcta. Para el molde con cavidad profunda, se debe agregar una ranura de escape y un orificio de ventilación en la parte debajo de la inyección. La ranura de ventilación con una profundidad de 0. 02-0. 04 mm y un ancho de 5-11 mm se puede abrir en la superficie de cierre. El orificio de ventilación se establecerá en la posición final de llenado de la cavidad del molde.
(6) In the aspect of process operation, we can improve the mold temperature, reduce the injection speed, reduce the resistance of the gating system, and reduce the closing force.
(7) La temperatura del molde es demasiado baja: el molde debe precalentarse a la temperatura requerida por el proceso antes de comenzar -. Si la temperatura del molde no aumenta, verifique si el diseño del canal de agua del molde es razonable.
(8) Insufficient injection pressure: the injection pressure and the length of the die are close to a positive proportion. The injection pressure is too small, the length of the die is short, and the cavity filling is not enough. Therefore, the injection pressure can be increased by slowing down the injection forward speed and extending the injection time appropriately.
& nbsp;
2、 Deformation
Debido a que la contracción interna del producto es inconsistente, la tensión interna es diferente y se produce la deformación.
Causas y contramedidas:
(1) Orientación molecular desequilibrada: para minimizar la deformación causada por diferentes orientaciones moleculares, se deben crear condiciones para reducir la deformación. Orientación del flujo y relajación del estrés de orientación: el método más efectivo es reducir la temperatura del plástico y la temperatura del molde. Cuando se utiliza este método, es mejor combinarlo con el tratamiento térmico de las piezas de plástico, de lo contrario, el efecto de reducir la diferencia de orientación molecular suele ser de corta duración -. El método de tratamiento es que la tensión de orientación en la parte plástica se puede eliminar en gran medida cuando la parte plástica se desmolda y se mantiene a una temperatura alta durante un cierto período de tiempo y luego se enfría lentamente a temperatura ambiente.
(2) Improper cooling: when designing the structure of plastic parts, the section thickness of each part should be consistent as much as possible, and the plastic parts must be kept in the mold for sufficient cooling setting time. For the design of mold cooling system, it must be noted that the cooling pipe should be set in the position where the temperature is easy to rise and the heat is relatively concentrated. For those parts which are easy to cool, slow cooling should be carried out as far as possible to make the cooling of all parts of the plastic parts balanced.
(3) the first mock exam is not enough. The edges are not light. The plastic parts have a slope when designing the mold. If a product & #39;s uneven slope is distorted, the product will be rough and rough. In the design and acceptance of the mold, the angle of the supporting film and the smoothness of the edge should be considered.
(4) Cooling time: when the vulcanized plastic is filled into the mold cavity, there must be cooling time. The cooling time will cause the product ejection deformation. The product is not sufficiently cooled. When ejection, the product will also deform if it is relatively soft. If it is too slow, the product will completely cool in the mold cavity and ejection has no elasticity. The hardtop product will also deform, so the cooling time should be set appropriately.
(5) Injection process: injection process, pressure, speed, time, location, can make the product deformation. When setting the parameters, it should be considered repeatedly. When adjusting the machine, adjust the parameters slowly in 1 unit to obtain the best parameters.
& nbsp;
3、 Phimosis
Cuando la masa fundida de plástico es expulsada del molde desde la superficie de separación. Se forma un destello cuando la cavidad produce una lámina.
Causas y contramedidas:
(1) Insufficient clamping force: when the clamping force of the injection molding machine is too low to maintain the clamping force of the mold, the flashing will occur. It is necessary to adjust the area of the plastic part and the molding pressure to see whether they exceed the rated clamping force of the equipment and improve the clamping force. If they exceed the limit, the machine with large tonnage can be replaced, and the injection pressure, mold temperature, injection speed, time and position can also be adjusted from the process of adjusting the machine.
(2) Material temperature is too high: the plastic temperature is too high, resulting in the melt viscosity is too low and the material overflows between the templates. You can manually spray glue to observe the fluidity of the raw materials. You should properly reduce the material temperature, and at the same time, try to precisely process the mold to reduce the mold gap.
(3) Mold defect: mold defect is the main cause of overflow flash. Carefully check whether there are sundries in the mold closing surface and guide pillar hole, resulting in the mold not being closed. Whether there is balance between the mold templates, whether there is bending deformation, and whether the opening distance of the template is adjusted to the correct position according to the thickness of the mold. Whether the lock module surface is damaged, whether the pull rod is deformed unevenly, and whether the exhaust slot hole is too large and too deep. If the formwork deformation is caused during forming, the supporting formwork or thickened formwork shall be added to prevent the formwork deformation.
(4) Improper control of process conditions: the injection speed is too fast, the injection time is too long, the injection pressure is not evenly distributed in the mold cavity, the filling speed is not balanced, and the feeding amount is too much, resulting in flash and drape. Taking corresponding measures to reduce the filling speed, especially the speed close to the completion of filling, the injection pressure and the holding pressure, can reduce the required clamping force and avoid using too low
